Custom-made work platform transporters
We manufacture custom-designed vehicles that are precisely tailored to your needs.
Our models include:
-
32-ton class with a payload of approximately 19 tons
-
26-ton class with a payload of approximately 14 tons
-
18-ton class with a payload of approximately 8.5 tons
The actual payload depends on the specific vehicle and body configuration. Together with you, we will develop the ideal vehicle concept that fully meets your requirements.
-
Subframe for low-profile construction, made of high-quality steel profiles, fully welded and fully galvanized
-
Frame offset at the vehicle overhang by 7°
-
Hydraulically controlled (lowering, raising and sliding) loading ramps (foldable)
-
We adapt our hydraulic system to your requirements, e.g. electro-hydraulics to enable quiet and reliable loading and unloading in residential areas, or driving the hydraulics via the vehicle's power take-off.
-
Hydraulic control unit, splash-proof and installed in a box
-
Electric or hydraulic winch with a pulling force of 6,800 kg; winches with greater pulling force are also available.
-
Platform floor made of heavy-duty grating laid flush with outer frame
-
Load securing devices approx. 5.0 t
-
Paintwork for flatbed vehicles is a single color in the cab color according to RAL; special designs are of course taken into account.
-
Front wall with devices for storing various lashing equipment
-
Plug-in climbing aid
Basic equipment
-
Dimensions:
-
Up to a maximum length of 9400 mm, usable length 9000 mm, depending on the chassis.
-
Width 2550 mm
-
Height 120 mm
-
Platform height varies between 1000 mm and 1070 mm depending on the chassis.
-
Chassis with wheel recesses have a height of 950 mm in this area (4 axles)
-
fully galvanized
-
Made from fully welded profile tubes to achieve high structural rigidity.
-
The rear is angled by 7° to achieve a shallow approach angle.
-
Four-axle chassis are equipped with two additional wheel recesses including covers to transport large equipment weighing up to 17.5 tons.
-
Outer frame painted in desired color
-
Lashing points distributed every 500 mm on the outer frame and longitudinal beams with a load capacity of 5 tons
-
Additional lashing points can be provided upon agreement.
-
The floor covering is optionally made of galvanized grating with slip resistance R12 or R13, laid flush with the outer frames; alternatively, a floor covering made of aluminum profiles can also be installed.
Support frame
-
Hydraulically operated with a tractive force of 6.8 tons
Winch
-
All functions of the loading ramp and winch can be controlled via a remote control.
-
In case of vehicle failure, all functions can be operated via an emergency hand pump.
-
The hydraulic system is splash-proof and housed in a stainless steel toolbox on the right side at the rear.
Hydraulics
-
3 toolboxes measuring 800x500x500 mm, made of stainless steel, mounted on the left side of the vehicle according to available space; other dimensions available upon request.
-
Including interior lighting for the "dark season"
Toolboxes
3.5 tons for 13-pin connector
Towbar
Possible from the vehicle's fuel tank or from a 300l auxiliary tank
The flow rate is 30l/min and it is equipped with a counter and an automatic dispensing nozzle.
Refueling station
-
Dimensions:
-
Total length: 4500 mm
-
Width 875 mm
-
Approach angle of approximately 8°
-
The access ramps are divided and hydraulically operated.
-
Ramps can be moved laterally 20mm beyond the outer frame and slid together in the middle to 25mm.
-
are suitable for loading at loading ramps
-
including integrated flashing light as a side warning marker
-
The floor covering consists of galvanized gratings with slip resistance R12 or R13.
Access ramps
-
Can be combined with other variants according to customer requirements
-
Aluminum front panel approx. 1200 mm coated with a rubber mat
-
2 work lights and a rear light for road safety
-
Side posts painted in desired color
-
Above: Aluminum shelf including lockable holder for lashing chains
Front wall (Variant 1)
-
Can be combined with other variants according to customer requirements
-
Flush with cab roof
-
Aluminum front panel approx. 1800 mm coated with a rubber mat
-
2 work lights and a rear light for road safety
-
2 aluminum storage boxes
-
Includes lockable holder for lashing chains
Front wall (Variant 2)
-
Can be combined with other variants according to customer requirements
-
Storage compartments are installed on the right and left as well as above the winch.
-
Flush with cab roof
-
Aluminum front panel approx. 1800 mm coated with a rubber mat
-
2 work lights and a rear light for road safety
-
2 aluminum storage boxes
-
Includes lockable holder for lashing chains
-
Shovel and broom holder on the back of the front wall
Front wall (Variant 3)
-
For special solutions, please contact us; we will find a way together.